Self-Attaching Small Black Sawtooth Hangers - Supports 7 Lbs
Self-Attaching Small Black Sawtooth Hangers - Supports 7 Lbs
About the Small Black Nailess Sawtooth Hangers Self-attaching no-nail sawtooth hangers for wood frames 1/4" wide x 1" long No additional hardware needed Steel with a black oxide finish Supports up to 7 lbs Made in the USA Made of tempered steel, each nailess sawtooth has two pronged "legs" that enable it to be attached to a wood picture frame without screws or nails. The hardened finish allows the hanger to be hammered into position without deforming.Nailess Sawtooth Hangers install very quickly - pilot holes are usually not necessary except for very hard woods like oak or ash. Instructions Lay the frame face down on a blanket or soft surface. The hanger should be installed centered left-to-right on the top rail, a little down from the upper edge of the frame. The small sawtooth has two serrated edges and.
About the Small Black Nailess Sawtooth Hangers
- Self-attaching no-nail sawtooth hangers for wood frames
- 1/4 wide x 1 long
- No additional hardware needed
- Steel with a black oxide finish
- Supports up to 7 lbs
- Made in the USA
Made of tempered steel, each nailess sawtooth has two pronged legs that enable it to be attached to a wood picture frame without screws or nails. The hardened finish allows the hanger to be hammered into position without deforming.
Nailess Sawtooth Hangers install very quickly - pilot holes are usually not necessary except for very hard woods like oak or ash.
Instructions
- Lay the frame face down on a blanket or soft surface.
- The hanger should be installed centered left-to-right on the top rail, a little down from the upper edge of the frame.
- The small sawtooth has two serrated edges and can be installed either way.
- Use a small hammer to tap the nailess sawtooth hanger in place.
- Take care not to break the glass on the frame, if any, when hammering in a nailess sawtooth hanger.
- In extremely hard woods, drill small pilot holes for the legs of the hanger.
- When properly seated, the shoulders of a nailess hanger should rest on the surface of the frame rail, leaving approximately 1/8 gap between the back of the hanger and the surface of the rail.
- Make sure that your nail in the wall is tight and secure before using it to hang the frame. Always use a headed nail (not a brad) and position the frame on the nail so that the nail is caught firmly on the sawtooth hanger.
Mounting Suggestions? - Everything Else - Glowforge Owners Forum
OOK Large Self-Leveling Sawtooth Hanger Zinc 3 Pack - Picture Hanging Hardware
Picture Hangers Adhesive - 10 Pack - Plastic Sawtooth Adhesive Picture Hanger - Foamboard Hanger
Sawtooth Picture Hangers - 100 Pack - Black Sawtooth Picture Hangers No Nail - 1 3/4 Inch Sawtooth Hangers
50 Pack Small Sawtooth Picture Hangers Picture Hangers Picture Frames Hangers with Screws Solutions for Picture Hang, Sawtooth Hangers Hardware
Sawtooth Hangers Large with Screws - 100 Pack - Canvas Hanger - Picture Frame Hanger
STAS self-fastening tooth hanger (4 pieces) - STAS picture hanging systems
Sunmns 150 Pack Sawtooth Picture Photo Frame Hangers Screws, Black
OOK 20 lbs. Steel Sawtooth Ring Hangers (3-Pack) 533824 - The Home Depot
Sawtooth Picture Hangers No Nail - 100 Pack - 1 3/4 Inch - Silver- Zinc Sawtooth Hangers : Tools & Home Improvement
Self adhesive hook - heavy duty adhesive picture hangers - STAS picture hanging systems
Command™ Universal Picture Hanger
Sawtooth Picture Hangers with Screws - 100 Pack - Small Sawtooth Hanger
